This may take few minutes. This needs to be a USB 1.1 compatible device formatted as FAT32. You can also use the file Liveburner IPK for updating this Kerlink firmware, to perform a factory reset. For example, if an iFemtoCell has 009CVc031234 as board ID, then the root password will be pdmk-031234 (case sensitive). Move to this directory under your SSH connection: where [KERLINK image file name] is the file name of the image (.tar.gz file) you previously downloaded and transferred in /home/root. Connecting the antenna. Create /user/.updates directory on the base station if not already created: Copy all ipk packages from the extracted from the package to /user/.updates directory: Initiate LRR package installation by executing the following commands, followed by a reboot of the base station: After running the command, the base station will be flashed with the ThingPark image. This method is valid for all Kerlink models except SOP4. To prevent Web robots from attacking the gateway with standard login/password root/root, default password is built using the last 6 characters of the board ID: pdmk-XXXXXX. It i s based on LoR a technology provided by Semtech Co mpany, it is compatible and interoperable with existing Lo Ra LPWAN. Provisioning Description The repository contains interactive provision.sh script, which can be used to provision Kerlink Wirnet gateways to route traffic to The Things Network Stack for LoRaWAN. Connect to the base station via SSH. You do need to request a login and password from Kerlink. This is useful in cases where you might want to customize installation by e.g. To optimize the radio performances, when possible, KERLINK strongly recommends to dissociate the antennas (LoRa and . Insert the USB install key into the IFEMTOCELL or IFEMTOCELL EVO gateway. To prevent Web robots from attacking the gateway with standard login/password "root/root", default password is built using the last 6 characters of the board ID: pdmk-XXXXXX. For Kerlink iStation, a USB Type C to USB-A adaptor would be required. The status shall show OK for the ipk packages installed. The usbkey password is unique per base station and can be retrieved based on its LRR ID or UID (UUID). The firmware consists of two parts: System Firmware (usually) from Kerlink Installed in / partition User Firmware from TTN/TTI/Partner Installed in /mnt/fsuser-1 partition Includes "global" configuration Kerlink Wirnet Station firmware updates are installed from a USB drive. Re-Assembly. If you press the Test button on the gateway you will see the MOD1 and MOD2 lights flashing. Hugo You can do so with the command: passwd. After downloading your ThingPark Enterprise base station image as described in Retrieving the base station image, follow the steps provided below to flash your base station with the new image. Note Flashing of Kerlink firmware 4.3.3 requires: liveburner_4.3.3_klkgw-signed.ipk (erase everything). If using an external 4G dongle, Insert the 4G dongle to the USB port on the other side of the iFemtocell. The Kerlink Wirnet product family share the same firmware and software architecture (for Wirnet iBTS, Wirnet iFemtoCell, Wirnet iFemtoCell-Evolution, Wirnet iStation). Functional check. Once installed, firmwares older than v3.1 cannot be installed anymore. For its direct customers, Kerlink is also providing: Access to technical documentation (Wiki) : Click here, Access to Assistance Request System (OTRS) : Click here. RAK2245 Pi Hat Edition - LoRaWAN Gateway Concentrator Module. Helium network customer support : Click here. Install with a USB install key. You can loggin as root with using as password pdmk-XXXXXX where XXXXXX is the end of the device id written on the back as BoardID. To directly address your issue you would need to find a way to alter a filesystem on the gateway. Once the LED is blinking, unplug the USB key. Find an empty USB key (FAT-32 formatted) and add the 3 files: Transfer the KerOS package corresponding to the new firmware in this directory (replace with, The gateway EUI can be found by using the command. Updated The Kerlink Wirnet iFemtoCell gateway is a LoRaWAN gateway perfectly designed for indoor public network extension or for ad-hoc indoor private coverage, like building or industrial sites requiring continuous connectivity for their IoT applications. The Kerlink packet forwarder is composed of the LoRa daemon (LoRa modem management) and the LoRa forwarder (connection to TTN), respectively called lorad and lorafwd. If the installation was performed successfully, verify that the LRR version installed on the base station is the expected one (refer to the compatibility matrix above). Has anyone tried mining HNT with a Kerlink hotspot? You may also perform factory reset with the USB install key prepared in Installing Kerlink Base Station with USB stick, proceed as below: Insert USB install key into the base station. Both ethernet and WiFi can be used (for WiFi, make sure to use the firmware 3.3.3. or later). Quickstart guide : Download Certificate of Conformity 868 : Download For its direct customers, Kerlink is also providing: A Wiki accesses* where it can be found a comprehensive set of documents and technical information An OTRS* (Open Ticket Resource System) for access to Assistance Request System Confirmed: Internet of Things (IoT) solutions provider Kerlink has announced three of its IoT gateways are now compatible with Helium's peer-to-peer wireless LoRaWAN network while enabling the mining of its native cryptocurrency *. Reddit and its partners use cookies and similar technologies to provide you with a better experience. The Gateway is shipped with Kerlinks stock system firmware. Wait around 20 seconds until the yellow LED on the debug port blinks very quickly. : Application server, Gateway, Hardware, Network Operator, Network planning, Network server, Platform, Services, Software, Turnkey Solution. See this forum topic. To ensure the Wirnet iFemtoCell is started up, check the behavior of the LED indicators: The first step is to log in into the gateway using ssh: ssh root@GATEWAY-IP-ADDRESS Please refer to the Kerlink wiki for login instructions. A firmware upgrade will most likely result in a factory reset of the gateway. After editing the contents of the dota_XXXX.tar.gz file, compress with tar -cvzf dota_upgrade.tar.gz --owner root --group root mnt usr (use gtar on macOS). RAK2245 Pi Hat Edition - LoRaWAN Gateway Concentrator Module. The LRR version can be verified via the SUPLOG menu (see Connecting to SUPLOG). You can find out more in this part. This firmware does not support previous hardware called LoRa station 20dBm sold until May 2015. The script prompts you before installing firmware and/or rebooting the gateway. It can only be used to access the iFemtoCell itself as it does not route traffic to anywhere and does not serve as an Internet wireless access point. Are you sure you want to create this branch? The list of files is given for information - actual file names may change depending on the firmware and LRR version: usbkey.txt (optional, only needed if LRR is already installed on the base station). Install the packet forwarder over the network or USB and reboot the gateway. This may take few minutes. A backup of this system firmware is kept for recovery purposes (on the rescue FS). SSH into the gateway. You can find out more in this part. Update the firmware # Check the firmware version using the command: cat /tmp/sys_startup_status.json Step 1. For example: gateway/# (subscribe to all gateways and all messages) The gw_id is probably printed outside of the gateway. Your computer may take some time to get the connected status, and the interface will have a limited connectivity, which is normal. Note that the Wiki access is private and requires login/password. Reddit, Inc. 2023. The Kerlink base station models supported are: All the Kerlink base station models share the same firmware version except for the Kerlink SOP4 model. This will however erase the whole partition and resets the default password. Follow these steps to reset a Kerlink base station: Connect to your base station as root user. 372003c Compare Wirnet Station Firmware 3.6 Wirnet Station Firmware 3.6 (March 2019) Changes from 3.3 New Features [Network] - DNS resolution in static IP. If your base station does not have any LRR software installed and is already with its factory configuration, proceed with the following steps to install the LRR software: Make sure the base station has been off for at least 10 minutes to ensure internal battery is completely discharged. Safely remove the flash drive from your computer. This process will take a couple of minutes. Plug the USB stick into the base station. Update the firmware From your LAN or WLAN you can access the gateway using ssh. If the procedure is not done correctly you stand a chance to brick your gateway. iFemtoCells are named after their serial number and are called klk-fevo-XXXXXX. Please read through this entire document before performing the firmware update. and update via the Kerlink Wanesy Management Center. Kerlink CPF services (lorad and lorafwd). Privacy Policy. By accepting all cookies, you agree to our use of cookies to deliver and maintain our services and site, improve the quality of Reddit, personalize Reddit content and advertising, and measure the effectiveness of advertising. The wirnet iFemtoCell Evolution is a low-cost, indoor LoRaWAN nano gateway that can be easily connected through GSM cellular or ethernet. Check that the IBTS or iStation is not rebooting: by default, IBTS or iStation reboots every 5 minutes. This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository. For example, if an iFemtoCell has 704BEc1234AB as board ID, the host name will be: klk-wifc-1234AB. First connection When the Wirnet iFemtoCell is installed, the first connection can be done by two different ways: Using Wi-Fi connection: o Press the WPS button (Wi-Fi Protected Setup) on the Wirnet iFemtoCell (see chapter 4 "Overview") then press the WPS button on the Wi-Fi access point of the installation o The connection will be established. Screw the antenna to the gold connector on the right-hand side of the gateway. Important If ThingPark LRR software has already been installed on the base station, you must first reset your base station to its factory settings. A WiFi access point is available at boot time on each iFemtoCell for one hour, broadcasting an SSID named after its serial number (klk-wifc-XXXXXX). script to create a custom network upgrade dota. Note: This was tested with the following firmware version: 5.5.4. Restrictions [Update] - Firmware update erases all partitions. This may take few minutes. Wait around 20 seconds until all 4 LEDs (2 on debug port + 2 on local port) blink very quickly, 3 LEDs only in the case of iFemtoCell. A log file is written back to USB drive (. Page 1 NSTALLATION AND AINTENANCE ANUAL IRNET EMTO Written by Approved by Approved by Validated by Name Entity Date 2018/11/16 2018/11/19 2018/11/21 2018/11/21. Important For the Kerlink base stations, except SOP4 models, that were initially installed with a firmware version different from 4.3.3, the base stationshould be flashed with liveburner of the firmware 4.3.3 before installing the new base stationimage. This method is valid for all Kerlink models (including SOP4). For security reasons, it is highly recommended to change the password. Page 4 Operating temperature range: -20C to +50C In case of 3G/4G connection with USB dongle: KERLINK recommends using a validated USB dongle (contact your reseller to have the list of validated USB dongles). Quickstart guide : Download Certificate of Conformity 868 : Download Certificate of Conformity 923 : Download For its direct customers, Kerlink is also providing: A Wiki accesses* where it can be found a comprehensive set of documents and technical information An OTRS* (Open Ticket Resource System) for access to Assistance Request System # reboot You can find more details using the link below https://wikikerlink.fr/wirnet-ifemtocell/doku.php?id=wirnet-ifemtocell:software_updates disk91.com - the IoT blog . Kerlink iFemtoCell. To prevent Web robots from attacking the gateway with standard login/password root/root, default password is built using the last 6 characters of the board ID: pdmk-XXXXXX. Before you can install the ChirpStack Concentratord, you must disable the Page 5: First Connection modifying the DOTA scripts. The firmware consists of two parts: WARNING: After installation of this firmware you will not be able to revert to v2.3.3 - an attempt will brick your gateway. I've heard on the jungle drums that you can now mine helium HNT with Kerlink hotspots. But an alternative is to run the lora-gateway-bridge on some other computer (such as the one hosting LoRaServer) and use a legacy protocol between the gateway and the bridge, meaning that the only thing you need to change on the gateway would hopefully be the address of the server it should . Kerlink Common Packet Forwarder v1.1.6 (October 2019). Once v3.6 installed, firmware older than v3.1 cannot be installed anymore (breaking for backward compatibility). The "Wirnet iFemtoCell" is the ideal gateway to support your smart city, smart building or every smart project that requests dedicated indoor coverage and/or network densification . Once the base station has rebooted, and is up and running, verify that the LRR version installed on the base station is the expected one (refer to the compatibility matrix above). New comments cannot be posted and votes cannot be cast. As a consequence, on a such miner, you should be synced within the day or it . This page describes how to install and configure any of these gateways. Gateways Kerlink Gateways hmullerenersa (Hugo) March 14, 2018, 6:21pm #21 hmullerenersa: Hi Tord where i can download this latest version of Packet Forward for ifemtocell spf_3.1.-klk15_4.1.3-klk7_klk_wifc.ipk ? Install Kerlinks latest packet forwarder which can be found under Kerlinks Resources section. Kerlink has been listed as an approved hotspot maker (link), however, no Onboarding Maker Address has been assigned as of yet. The user firmware can be updated with dota_XXXX.tar.gz and custo_XXXX.tar.gz files. Archived post. KERLINK Gateway. The gateway will detect the firmware file on the flash drive and start installing it. usbkey.txt: contains passphrase which allows usb.autorun to be executed. The Gateway is usually shipped without or with outdated user firmware. To check the current Kerlink firmware version of your base station: root@klk-wifc-030218:~ # cat /tmp/sys_startup_status.json | grep sw_version Refer to Kerlink documentation and support for details on how to flash the 4.3.3 version of Kerlink firmware. All rights reserved. Use the following commands to trigger a factory reset: At this stage, your base station will reboot and restore stock settings. chirpstack-concentratord package: Run the following command to install the IPK package: Use the following commands to (re)start and stop the ChirpStack Concentratord Source & further info This repository contains firmware and tools used to connect Kerlink Wirnet gateways to The Things Network Stack for LoRaWAN. klk-fevo-031234 login: root Password: pdmk-031234. Edit that file (for example /user/etc/lorafwd/lorafwd.toml), and scroll to the [ gwmp ] section (around line 81) and configure the server address and ports: Write down the gateway EUI, youll need it later for registering the gateway in the Developer Console. Refer Kerlink Wiki. If you dont have yet your login/password, for your WIKI access or OTRS (Open Ticket Resource System), please ask for them to support@kerlink.com (the Product Id or any serial number of your Kerlink product will be required). For its direct customers, Kerlink is also providing: Access to technical documentation (Wiki) :Click here, Access to Assistance Request System (OTRS):Click here. You can wait 3 minutes after the last reboot. Screw the antenna to the gold connector on the right-hand side of the iFemtocell. A tag already exists with the provided branch name. Your Kerlink gateway should already be switched on and booted up. TheThingsNetwork/kerlink-wirnet-firmware, This commit was created on GitHub.com and signed with GitHubs, This commit was signed with the committers. A factory reset can be performed by doing a firmware upgrade using a USB flash drive. To use the gateway, you need to install the packet forwarder. Wait around 20 seconds, until the ethernet port blinks. This will trigger a reboot of the base station and will restore the factory settings. Copy the downloaded firmware using SCP command in the /user/.updates folder # scp keros_2.4.0..ipk root@<ip_address>:/user/.updates/ Trigger the update for next reboot # kerosd -u Reboot the device.